3/11/2023 0 Comments Github xscope gabotronicsOn my board, I switched these two around, so when the COM port is connected, the red LED turns on. The bottom LED (LED1) is the 'Status' LED and is typically red. The top LED (LED2) is the 'Connect' LED for the Bluetooth module, and is typically green. The 3V3 for the module is derived from the 3V3 output on the Xprotolab therefore, it will work whether powered by the DC barrel jack or the USB connector on the Xprotolab. View datasheets for Xscopes Manual by SparkFun Electronics and other related components here. To connect the Bluetooth module, I had to use air wires to connect to the expansion jack on the right of the Xprotolab, since these pins are not broken out anywhere else. The Xprotolab and Xminilab can be plugged directly on a breadboard. The XScopes can also be used as development boards for the AVR XMEGA microcontroller. To connect these, I used 0.024 inch traces on the top layer, with vias connecting the top and bottom ground planes surrounding them in an attempt to shield the traces. The XScopes The XScopes are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator and a protocol sniffer. The BNC jacks are from Sparkfun therefore, the parts used in Eagle are from the Sparkfun library (linked in the GitHub repository below). To make this board, I first created the schematic and board layout, then sent this to OSH Park for production. Two rows of I/O pin headers are used to bring the Xprotolab I/O pins to the edge of the board. In addition, this board also adds a 5V switching regulator so that the Xprotolab can be supplied by a 6.3-30V power supply, as well as a Bluetooth module that allows the wireless use of the Gabotronics Xscope computer interface. ![]() Therefore, this breakout board converts the two analog inputs, arbitrary waveform generator, and trigger pins to BNC jacks. ![]() sensors, frequency counters, etc.) or with oscilloscope probes. However, it is sometimes necessary to use this oscilloscope with other instruments that use BNC connections (i.e. The awesome functionality-to-size ratio is due, in part, to the ATXMEGA32A4U microcontroller on board.The XMEGA Xprotolab is a convenient mixed-signal oscilloscope (MSO) with an arbitrary waveform generator fitted to a DIP form factor. xScope is a powerful set of tools for Mac OS X that are ideal for measuring, aligning and inspecting on-screen graphics and. The scope itself obviously allows simultaneous sampling of analog and digital signals but also has several advanced trigger modes, XY mode for plotting Lissajous patterns, phase differences or V/I curves, Spectrum Analyzer with different windowing options and even an arbitrary waveform generator with sweep on all parameters. node-xscope is a node.js package for working with a Gabotronics Xminilab oscilloscope: controlling its operating configuration and processing the data that it. ![]() You can also connect it to your PC and use Gabotronics' XScopes software to control the device and view waveforms. Interactively examine a C program source in emacs Cscope is a program that generates index tables from C and C++ source files. The on-board graphic OLED matrix can display waveforms, measurements and menu systems. At only 1 x 1.6 inches, this oscilloscope can be plugged *directly into a breadboard. ![]() The XMEGA Xprotolab is exactly that: The first ever mixed signal oscilloscope, logic analyzer and arbitrary waveform generator in a DIP module. What you probably don't *imagine is a DIP package. PC interface is open source under the GPLv3 license and is available on GitHub. When you think about a piece of equipment like a mixed signal oscilloscope you usually think of, well, a piece of equipment. XScope: Xprotolab, Xminilab, Xprotolab Portable or Xminilab Portable.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |